• 2021-12-31

How to use floor grinder Floor grinding machine performance includes: grinding width, grinding head operation mode, speed, grinding head unit pressure, water control, etc. The construction standards are divided into: flatness, clarity and gloss. Floor grinding machine grinding head operation mode: the more complex the operation mode of the floor grinder grinding head, the greater the grinding force, the higher the work efficiency, and the improvement of ground clarity. Two-way 12 floor grinder speed: Under normal circumstances, the higher the rotation speed of the ground grinder head, the higher the grinding force. However, a too high rotation speed will reduce the grinding force of the abrasive and the ground. When the pressure of the grinding head is relatively low, it will reduce the stability of the machine operation and reduce the construction standards. The unit pressure of the grinding head of the floor grinder: the pressure of the grinding head of the floor grinder and the weight of the machine. The greater the pressure of the grinding head, the higher the relative efficiency and leveling rate. When the ground is too soft, if the grinding head pressure is high and the cutting force increases, the floor grinder cannot run at a uniform speed at this time, which will reduce the construction flatness.

• 2021-12-29

Will uneven ground affect the paving of emery ground? The abrasion resistance and compressive performance of emery floors are better than concrete and terrazzo floors. Now many factory floors are made of emery wear-resistant floors. The emery is formed by mixing emery in the process of cement pouring and solidifying as a whole. During this construction process, it is necessary to ensure the flatness of the cement floor is good, otherwise it will affect the paving of the emery floor. If the emery is placed less and the ground level is not good enough, the emery ground after finishing will show unevenness. Because the ground is uneven, when the emery is sprinkled, there are more deep places and less shallow places. The finished ground effect is like a flower. 1. Use a floor grinder for grinding and leveling. The emery floor is uneven and looks uneven. You can use a floor grinder for grinding and leveling. If the amount of sprinkled emery is small, the floor grinder may grind through accidentally when grinding, but not all When worn off, markings will appear in the deep, that is, the recessed area. 2. Try to use black colorant to avoid uneven ground.

• 2021-12-28

How to inspect the newfloor grinding machine With the prosperity of the floor market, the number of manufacturers of concrete floor grinders has increased, and the number of people engaged in the floor industry has also grown. The consumer concept of customers has gradually shifted from low price to everything to value quality and service. How to judge the quality of the machine is very obvious. important. In real life, some customers reported that after they purchased the floor grinder, the parts were loosened after using it a few times. At this time, they asked the manufacturer for the theory, but the other party shied away the responsibility by saying "you used it improperly". In order to ensure the legitimate rights and interests of consumers, Xingyi Machinery reminds you that when you receive the purchased floor grinder, you must inspect the goods as soon as possible: check the firmness of the overall frame and whether there is any looseness in the connection parts; Whether the motor, gear box cover, water tank is damaged, whether the power connector has fallen off, etc., please contact the freight station or the manufacturer in time. Xingyi Machinery is a professional manufacturer of floor grinding machinery. After more than ten years of development, it not only guarantees product quality, but also has established a complete service system, from R&D and production to sales to after-sales, strictly regulated For each process, select professional personnel. "One-minute response, 24-hour service", we will patiently listen to your problems, formulate professional solutions for you, and serve you better, so that you have no worries when using our machines.

• 2021-12-23

Hardened floor sanding, concrete sanding machine, epoxy floor sanding, curing agent floor sanding, wear-resistant floor sanding, resin floor sanding and other series of floor sanding; floor sanding machine is mainly used for ground grinding and sanding Treatment, it can effectively polish terrazzo, granite, emery, concrete surface, epoxy mortar layer and old epoxy floor. It has the characteristics of lightness, flexibility, and high work efficiency. With a vacuum cleaner power socket, the vacuum cleaner power cord can be directly connected to the grinder, avoiding the trouble of two power cords when working. It is necessary equipment for large-scale floor engineering treatment. Detailed introduction of the floor sanding machine: According to the different hardness of the stone, the wheels can move back and forth to reduce or increase the pressure during grinding. The speed can be adjusted appropriately, which greatly improves the renovation effect and reduces the cost. Equipped with extra-high-power motor, strong power output, can work continuously for 24 hours; the grinding disc can be replaced, refurbished, polished, crystal face, cleaning, one machine in place; folding design, separate counterweight, reduce the burden of handling; floor sanding machine It is a multifunctional machine and equipment that integrates different processes such as rapid floor polishing, floor hardening, epoxy floor treatment, floor leveling, sanding, and polishing.

• 2021-12-23

Winding method of the electric wire during construction of concrete floor grinder In the construction process, if you want to do the floor work more efficiently and safely, you also need to pay attention to the working wires of the concrete floor grinder. The wires are very long. If they are placed on the ground randomly, the machine will be easily touched back and forth. Therefore, in the working process of the ground grinder, the winding method of the wire is particularly important, which can greatly improve your work efficiency and improve your safety in use. Xingyi Machinery will give you a trick. The specific operations are as follows: 1. Plug in the external power supply; 2. Pass the power cord through the swing lever handle; 3. Wrap the power cord at least two turns on one side of the handle; 4. Pull the power cord slightly to ensure that the power cord has enough friction to make the power cord firmly fixed on the handle. Precautions: 1. Ensure that the power plug and socket are firmly connected; 2. Before plugging in the power plug, make sure that the emergency stop has been pressed and other switches have been reset; 3. Please use the power cord according to the minimum specification of the wire; 4. Please use the correct power supply. In addition, the grinding method of the concrete floor grinder also affects the placement of the wires. The best grinding line is to grind the ground according to the "#" character when grinding the ground so that the grinding effect will be better. . When grinding the ground according to #, the direction of the grinder should be such that the wire is pulled farther and farther, so as to further prevent the wire from interfering with the normal operation of the floor grinder. In the construction process, if you want to do the floor work more efficiently and safely, you need to pay attention to it. If you are still worrying about the working wires of the floor grinder, don’t give it a try, the floor construction will become more and more efficient, and you don’t have to worry about the wires being caught in the machine or the randomly stacked wires that trip people.

• 2021-12-11

How to distinguish the quality of floor grinders The floor grinder is mainly used for related construction operations on the ground. It can effectively grind the water stone, epoxy mortar layer and concrete surface, etc., to grind the floor more smoothly, smoothly and clearly. Pay attention to the following four points to know if it is good or bad: 1. Reliability of operation. To understand the failure rate of machinery, safety is always the most important. 2. The result of ground grinding, observe its flatness, lubricity, gloss, etc. after grinding the ground. 3. Stability of operation. Stable operation is the condition to ensure the stable operation of the machine, which can reduce the failure rate of the machine. 4. The grinding speed, grinding speed determines the operating efficiency, the operating speed of a floor grinder will directly affect the construction cost of the enterprise and the profit of the enterprise. Finally, please note that you must read the instruction manual before using the floor grinder, and someone should be there to help you.

• 2021-11-30

Seven polishing methods for marble Marble decoration is often used for cabinet countertops or floor decoration, and has the characteristics of beautiful decoration and good wear resistance. The marble needs to be polished during use, otherwise it will affect the gloss of the marble surface. So what are the marble stone polishing methods? 1. Dry grinding There are many steps in marble polishing, and it is very complicated. The first step is dry grinding. The purpose of dry grinding is to "peel" the marble. You need to use a stone refurbishment machine to remove stains on the surface of the stone, and polish to make the pores of the stone fine. 2.Dealing with stone stains There are usually many stains on the marble surface, so to polish the marble better, you need to deal with the surface stains. If the stain is difficult to handle, you can use some chemical treatment, then the stain is easy to remove. 3.Waterproof Waterproof treatment is also a good foundation for marble polishing. Waterproof treatment is mainly to prevent wet grinding in the later stage. Some sewage enters the stone, which will have a certain impact on the polishing, and the sewage entering the interior will also affect the quality of the marble. 4. Cut and fill gaps  In order to ensure that the marble surface is very beautiful, slitting, caulking and uniform slitting are very important. The easiest way is to patch the glue, which can easily achieve the beautiful effect. 5. Simple stone polishing Simple stone polishing can be waxed, cleaned, and then polished with steel wool. 6. Surface crystallization Use the crystal surface machine, scouring pad and crystal powder to make a protective layer on the surface of the marble to prevent stains on the stone, prevent scratches, and improve the brightness of the stone. It is understood that the duration of this protection is about one year. 7. Waxing Waxing can also increase the brightness of the marble and also protect the surface of the marble. The validity period of waxing can be maintained for 3 months. But it is not recommended to wax.

• 2021-11-27

Technical terminology of the flooring industry 1. Tack-free time For a certain thickness of wet paint film, the time it takes for the surface to change from liquid to solid 2. Working time The time required from the application of a certain thickness of the liquid paint film to the formation of a solid paint film 3. Transparency Transparency can indicate whether varnishes and paints contain mechanical impurities and the ability of turbid substances to transmit light 4. Density Under the specified humidity, the common unit of mass per unit volume of an object is kilogram per cubic meter (kg/m3), gram per cubic centimeter (g/cm3) 5. Viscosity The internal resistance of a liquid to flow 6. Solid content The amount of non-volatile matter contained in the coating is generally expressed as a percentage of the mass of the non-volatile matter, and can also be expressed as a volume percentage 7. Storage stability Under the specified conditions, the degree of resistance of the coating product to changes in performance such as peculiar smell, consistency, crusting, coarsening, sinking, agglomeration, etc. after storage 8. Compatibility The ability to mix one product with another without causing adverse consequences (such as precipitation, coagulation, thickening, etc.) 9. Grinding fineness A measure of the degree of dispersion of pigments and extender pigments in paints, that is, under specified conditions, the reading obtained on a standard fineness meter. This reading indicates the depth of a groove on the fineness meter, generally expressed in microns. 10. Hiding power The ability of the color paint to eliminate the color or color difference on the substrate 11. Recoatability The difficulty and effect of multi-layer coating of the same paint 12. Paint film thickness A measure of the thickness of the paint film, generally expressed in microns 13. gloss An optical property of a surface is expressed by its ability to reflect light 14. Constructability The difficulty of paint application. Good paint application. Generally, it means that the paint is easy to apply and has good leveling, no sagging, wrinkling, edge shrinkage, bleeding, biting, moderate dryness, easy sanding, and good recoatability. And low requirements for construction environmental conditions 15. Adhesion The firmness of the bond between the paint film and the coated surface The coated surface can be a bare substrate or a painted substrate 16. Hardness The ability of the paint film to resist mechanical forces such as collision, depression, scratching, etc. 17.flexibility The ability of the paint film to deform with its substrate without being damaged 18. Wear resistance Resistance of paint film to friction 19. yellowing The tendency of the paint film to turn yellow during the aging process 20. Temperature resistance The ability of the paint film to maintain its original performance after being subjected to alternating temperature changes with cold and heat 21. Send flowers Color paints contai...